Saskatchewan Professional Driver Test 06

By using this practice test, you’ll better understand what areas you need to work on before the actual test day. With diligent studying and practice, you can pass your official exam with flying colors! Plus, your thorough preparation will make you feel more knowledgeable and confident on the road.

1 / 30

While inspecting the brakes on a class 3 vehicle, which of the following is not inspected?

Must not exceed manufacturer's wear limit

Excessive wear on discs

Excessive wear inside the drum

Excessive wear on the pedal

2 / 30

While inspecting the rims of a class 3 vehicle, what are you looking for?

Damage or cracks

Rust

Wrong size

All of these

3 / 30

Which answer is false? All mirrors must be...

Clear

Working

Not damaged

Unobstructed

4 / 30

If there are multiples of the same item on the vehicle, should you inspect each item the same way?

Do half of them

Yes

Only do the important ones

5 / 30

A minimum of how many flares/reflectors must be present if vehicle is wider than 2,060 mm and being operated outside corporate limits of an urban municipality?

Two

Eight

Five

Three

6 / 30

Which answer is false? While inspecting the hubs, they must not be...

Old

Distorted

Cracked

Bent

7 / 30

When performing a class 2 bus trip inspection, which fluid is not checked?

Brake fluid

Power steering fluid

Engine coolant

Engine oil

8 / 30

While inspecting the engines belts for a heavy trailer endorsement, which of the following is not checked?

Cracks and fraying

Size

Wear

Tension

9 / 30

While inspecting the tires of a heavy trailer endorsement, which of the following is not checked?

Tread separation

Proper inflation

Damages, cuts or bulges on the sidewall

Missing valve stem cap

10 / 30

While inspecting coupling devices (fifth wheel, pintle hitch, draw bar or ball hitch), which of the following is not checked?

Must be in the locked position and locked by the applicable locking device such as a pin or jaws of a fifth wheel

Coupling device must be securely attached to the vehicle

Safety chains attached to the trailer cannot be rusted

Must be properly coupled to the trailer

11 / 30

While inspecting the tires of a class 3 vehicle, which of the following is not checked?

Damages, cuts or bulges on the sidewall

Proper inflation

Tread separation

Valve stem cap

12 / 30

Which statement is false? While inspecting the landing gear and handle of the heavy trailer, Landing gear must be...

Not damaged

Raised

Not missing

Secure

13 / 30

While inspecting windshield wipers and washer for a class 4 vehicle inspection, which of the following is not inspected?

Turn on the windshield washer to make sure it works properly

Check for correct size

Make sure they wipe properly

Check the wipers for damage

14 / 30

When testing the trailer service brakes, what should be done?

Release all park brakes, drive quickly ahead and apply the trailer brakes using the foot valve

Release all park brakes, drive slowly ahead and apply the trailer brakes using the hand valve (spike), if equipped

Release all park brakes, drive slowly ahead and apply the trailer brakes using the foot valve

Release all park brakes, drive quickly ahead and apply the trailer brakes using the hand valve (spike), if equipped

15 / 30

Are class 3 vehicles required to have mud guards?

Just in winter

Yes

Only in spring and fall

16 / 30

While inspecting the trailer of a class 1 vehicle, with the trailer emergency brakes applied and the truck park brakes released, what is needed to test the emergency application of the trailer brakes?

Firmly press the accelerator

Try to gently pull away

All of these

Shift into neutral and see if it rolls

17 / 30

While inspecting the tractor of a class 1 vehicle, with the truck park brakes applied and the trailer emergency brakes released, what is needed to test the application of the truck park brakes?

Firmly press the accelerator

All of these

Try to gently pull ahead

Shift to neutral and see if it rolls

18 / 30

While inspecting the doors of a class 3 vehicle, which of the following is not inspected?

Must not be damaged

Must be securely fastened to the vehicle

Hinges are secure and worn

Must open and close properly

19 / 30

When testing the truck service brakes, what should be done?

Release the hand valve, drive quickly ahead and make a foot brake application using the foot valve

Release the hand valve, drive slowly ahead and make a foot brake application using the hand valve

Release the hand valve, drive quickly ahead and make a foot brake application using the hand valve

Release the hand valve, drive slowly ahead and make a foot brake application using the foot valve

20 / 30

While inspecting hoses for a class 4 vehicle, which of the following is not checked?

Fraying

Engine oil

Leaks

Poor connections

21 / 30

When conducting a heavy trailer inspection, what has to be inspected?

The truck and trailer

The trailer brakes

Only the section that connects the trailer to the truck

Just the trailer

22 / 30

While inspecting windshield wipers and washer for a heavy trailer endorsement inspection, which of the following is not inspected?

Make sure they wipe properly

Check for correct size

Turn on the windshield washer to make sure it works properly

Check the wipers for damage

23 / 30

Where would you need to check for fluid leaks?

All of these

From the filler cap

At the gas tank

Under the vehicle

24 / 30

What would indicate a loose lug nut?

All of these

Rust or shiny rings around the contact surfaces

A missing lug

Squeaking

25 / 30

While inspecting the rims of a heavy trailer endorsement, what are you looking for?

All of these

Wrong size

Damage or cracks

Rust

26 / 30

While checking the steering during a heavy trailer endorsement inspection, what should you look for?

Excessive free play

All of these

Power-assist

Power

27 / 30

While checking the steering, what should you look for?

Power-assist

Power

Free play

All of these

28 / 30

Which statement is false? While inspecting the heavy trailer, check all suspension components on each axle including...

Deflated air bags

Loose U-bolts

Cracked or broken springs

Leaking shocks

29 / 30

While inspecting the engines belts for a class 4 vehicle, which of the following is not checked?

Wear

Tension

Cracks and fraying

Size

30 / 30

While inspecting the switches inside the cab of a class 3 vehicle, does the engine need to be running?

Yes, definitely

No, but the key should be switched on

None of these

Only for select switches

Your score is

Saskatchewan Professional Driver Test 06

About

Practice Tests

Getting a License

Get In Touch